Search:

We adjust with the wheel off the ground, rear tire raised with the axle tight but just loose enough so that the tension adjusters can still move the axle rearward. We only adjust rearward. If we need...

Make it easy on yourself. If you can get one for less locally, I would go that route. You don't have to get it from me. But I'm glad you're doing it. I think you will be much better off when able to...

I would not run a belt very long after such an adjustment without getting the tension checked. The Krikit II tension gauge is very inexpensive and easy to use. A lot cheaper than a new belt or wheel...

I am a bit surprised. Tension and tracking are 2 sides of the same coin. One always affects the other. With the price of a Krikit II to check tension, I'm not sure why you would take this approach.

You have a very special wife... :thumbup:

I've got a million Lamont stories. I loved following him around just to see what would happen. Something always did...

I think the problem will be quite evident once they get into the CVT. I doubt the tech will have much trouble finding the cause.

AHHH! Too Bad! What's a little torque between friends?

Lamont's Boss Hoss had do much torque it would stand the bike up off the kickstand when he remote started it. And the kickstand had it leaned...

You're lucky to get much over 110 mph. The windshield makes a BIG difference. I went from almost no windshield to a small one on my 2008 GS and lost over 10mph top speed. Extrapolate this to the barn...

Any of the options offered will do you fine. You're probably wasting your money to change oil sooner than 3,000 miles. But if it makes you feel better, the cost may be worth it.

I must admit. I don't think I could do it. If someone told me I couldn't run wide open. I don't think I'd own a motorcycle.

Now that is quite remarkable.

Asking just out of curiosity. I like to observe how people ride. At our recent rally I watched the different ways people pulled out of the parking lot. We all have our own personal style. That's one...

It is ironic that the very purpose and one great advantage of the CVT system is in its ability to maintain a consistent, unvarying engine RPM.

In Tennessee, you can get a 'Motorcycle' (2 wheel) license qualifying on a Spyder.

The OP states 'Under the Seat'. Sounds like CVT chatter to me and not a driveshaft issue. The driveshaft on the Ryker is pretty bullet proof. Not saying it couldn't be the driveshaft. But why would a...

So, you're saying that you can't easily spin your wheels with the brakes disengaged? You need to re-do the install if this is the case. Not a good idea to wear down a set of pads by having them...

You should run at least 2 increments (we do 3) or phases on the torque process. If you torque one lug nut to full spec with the other 2 loose, that can warp your rotor.

That is unusual. Using the wrong torque procedure could warp the rotors. But this is fairly hard to do. Do you have a runout gauge to check your rotors with?

Rode my friends Royal Enfield 350 in Kathmandu, Nepal. All 18 hp of it! A modern 1950's motorcycle. 350cc is a BIG motorcycle in Nepal where most are in the 150-185cc range. His was carbureted...

Both of the issues referenced in this link were 998 V-Twins. Not sure this relates meaningfully to the 1330 motors.

What, exactly, did you do on your 'Brake Change'?

May Birthdays are the BEST!!!:thumbup:

208232

It's normal. You're fine...

Have you watched this video?
https://www.youtube.com/watch?v=wRFP2NQXnFE

AWESOME! Looks like you nailed it. There are some other DIY mods that can make the 998 much less issue prone. As far as lighting (or any electronic add-ons), you'll find the Spyder to be very...

We've only seen failure due to improper service installs (usually water pump related). Not to say that they don't fail naturally. Just not sure how concerned we should be about it?!

It's his nature... Probably comes from years of trying to miss Roos!

Some like to reinvent the wheel. But when you realize that the Krikit gauge is much more accurate than needed to start with. Adding accuracy with a high tech approach isn't worth the effort. The...

Yes, 2014-2019 will fit and work very well. 2013 will also fit but they are terrible shocks. Don't bother with them.