How to Fix Hyperflash in Directional Signals??

[CapeSpyder]

Does it hyperflash on both sides?
When I had HF on my last ryde, I put in 2 of the fixes and voila, no more HF!

Sent From my Note 5

 

[Rotax]

I installed an LED set up on my F3-S that allows the LED above the taillights to flash when I apply the brakes.
The only issue now is that my turn signals hyper flash.
Has anyone else experienced this?
If yes, how did you get the signals back on normal flashing?
Rotax

 

[Copperman]

Check with either Spyderpops or Lamonster Garage. They have the directions to stop the hyperflashing.

 

[Stubby]

With the engine running, hold the emergency flasher button down for 30 seconds. Worked for me.

 

[Spyder_Cowgirl]

Lamont has a video ... here's a link (it's more than just holding the flasher button down; you also have to reprogram the flash).

http://www.lamonstergarage.com/news/resetting-hyper-flash-after-adding-led-lighting/

All the best ... Ann

 

[Stubby]

With engine running hold the emergency flasher button down for 30 seconds.

 

[Catalyst105]

I’ve followed the video and tried 4 times. In the video he has the engine off, and it works with the engine off (hyperflash stops), but hyperflash returns when the engine is running.

 

[BLUEKNIGHT911]

I installed an LED set up on my F3-S that allows the Led above the taillights to flash when I apply the brakes.
The only issues is that now my turn signals hyper flash.
Has anyone experienced this?
If yes, how did U get the signals back on normal flashing?
Rotax

" Hyperflashing " ..... Folks here spend multi hundreds of dollars for numerous types of lights - why - because they want to be seen / noticed etc. many say it's for Safety reasons ..... So I think Hyper-flashing is a good thing ..... In my State ( Vt. ) under the Mtc. inspection rules " Hyperflashing " isn't " a violation ...... imho be glad you have it ...... Mike :thumbup:

 

[Bill]

Worked for me too!

 

[newbert]

Two years ago, I had additional directional lights installed (by TricLED) on the back of my 2016 F3-T. Thankfully, the original OEM turn signals remain functional both on the dashboard and in the back, so I'm still "legal".

Recently, the right-side light installed by TricLED doesn't work, and the original OEM turn signal is flashing at a high rate. Left side functions normally.

I remember reading about solutions to "hyper-flashing" quite a while back. Is that what's happening here? If so, or even if not, can anyone explain how to fix this?

Thanks!
Bert

 

[Smokes]

Two years ago, I had additional directional lights installed (by TricLED) on the back of my 2016 F3-T. Thankfully, the original OEM turn signals remain functional both on the dashboard and in the back, so I'm still "legal".

Recently, the right-side light installed by TricLED doesn't work, and the original OEM turn signal is flashing at a high rate. Left side functions normally.

I remember reading about solutions to "hyper-flashing" quite awhile back. Is that what's happening here? If so, or even if not, can anyone explain how to fix this?

Thanks!
Bert

1 Start the bike

2 Hold down the hazard light switch for 30-45 seconds

3 Turn the hazards off and put the right turn signal on and turn the bike off immediately the right signal flashes once.

4 Repeat for the left side

(copied from somewhere, can't remember where. It worked for my 2016 F3L.)

Good luck.

 

[Steve W.]

I would like to add item 2a.

2a. While holding the hazard light switch down, watch all the warning lights in the gauges carefully. They will flash VERY quickly at some point. After they flash, you can release the hazard switch. (Ours took about 20 seconds.)

.

 

[Rattlebars]

Two years ago, I had additional directional lights installed (by TricLED) on the back of my 2016 F3-T. Thankfully, the original OEM turn signals remain functional both on the dashboard and in the back, so I'm still "legal".

Recently, the right-side light installed by TricLED doesn't work, and the original OEM turn signal is flashing at a high rate. Left side functions normally.

I remember reading about solutions to "hyper-flashing" quite awhile back. Is that what's happening here? If so, or even if not, can anyone explain how to fix this?

Thanks!
Bert

Bert. Please always give the year of your bike. They change most everything each year and consistency on solutions is patchy. Contact TricLED for a replacement of the side light. Sometimes they die.

I would like to add item 2a.

2a. While holding the hazard light switch down, watch all the warning lights in the gauges carefully. They will flash VERY quickly at some point. After they flash, you can release the hazard switch. (Ours took about 20 seconds.)

Does this solution work for all years?? Reports of this NOT working on post 2017 models abound. I have asked this question many times but cannot get verification from a reliable source.

 

[lyntis]

Thanks. This worked. I didn't start the process with the key in the off position until your instructions. Perfect!