NHTSA Campaign 26V575000 - 2025-2026 Spyder RT, F3, & Canyon freezing cluster fix issued

[jfischer]

Weird, my 2024 shows no update available and I'm on 4.1.0 I hope 4.1.0 isn't bugged as well from future updates?

 

[mecsw500]

My 2026 Sea to Sky was delivered with V 4.1.0. I upgrades to V 5.1.0 after I took delivery. On the 17th I upgraded to V 6.1.0.

I wonder if someone who upgraded on the 16th just cannot upgrade again - just can’t, despite the options still showing; or have the online updating menu entries disappeared from the menu system?

What does that “cannot upgrade again over the air” actually look like on the cluster - if anything?

 

[jfischer]

My Spyder is almost impossible to connect to WiFi at my house. It usually takes 10-20 times, then it says bad password, even though it's stored correctly. I usually have to ride it somewhere where there's not much WiFi around, then use my phone hotspot. I tried that this morning too, but it still says no update available.

 

[mecsw500]

My Spyder is almost impossible to connect to WiFi at my house. It usually takes 10-20 times, then it says bad password, even though it's stored correctly. I usually have to ride it somewhere where there's not much WiFi around, then use my phone hotspot. I tried that this morning too, but it still says no update available.

Bluetooth can interfere with 2.4GHz WiFi. I’d try disconnecting all Bluetooth connections with the Spyder, if you have any, to see if that makes things better.

It seems like perhaps your local 2.4GHz network is very crowded and maybe the signal strength in your garage is low. You might want to load a network app on your phone to see if there is a less crowded channel is available to use as the router’s default. If your router is automatically choosing channels, then its view of the crowd may be different to the situation in your garage where the signal strength is likely lower too.

If your router is the one supplied by your network provider, cable or fiber, then often it is better to set that into bridge mode and provide your own higher quality device. The provided units are built down to a price. You can usually get a device that's a whole lot better, especially in the 2.4GHz band, for well under $100. Some are better than others about negotiating the security handshake in noisy and faint signal environments. Some of the network provider’s devices are pretty poor in my opinion and leave a lot to be desired.

When I had AT&T cable, before Google Fiber, I provided my own cable modem and router, saving me the monthly rental fee for their device and improving the network coverage enormously.

Now, with Google Fiber, I have a lot more sophisticated networking topology, but just about anything is better than the provider’s equipment..

 

[jfischer]

Thanks @mecsw500, I have my own WiFi equipment, and separate SSIDs for 2.4 and 5 GHz channels. When I browse for WiFi on my computer I probably see at least 20 different SSIDs, and this is in a single family neighborhood. The Spyder has never worked very well on WiFi for me, rarely connecting at all. If I go to a remote-ish area with good cell service, I can connect to my phone's hotspot first time, every time. That's how I did the first update or two actually. But so far it just tells me there's no update available even with my hotspot in a "clean" area.

 

[mecsw500]

Weird, what release does your bike tell you it has?

 

[K&R]

Updated my 2024 Spyder Ltd this morning to the V6 version. It took about twenty minutes. Everything seems fine now, altho some of the icons have moved and there's new graphics. I had the screen freeze up on me, but only while parked. I just go through the start procedure, it starts, and seconds later the screen activates. I've never had it blank out while riding. Just lucky, I guess?!

 

[mecsw500]

Updated my 2024 Spyder Ltd this morning to the V6 version. It took about twenty minutes. Everything seems fine now, altho some of the icons have moved and there's new graphics. I had the screen freeze up on me, but only while parked. I just go through the start procedure, it starts, and seconds later the screen activates. I've never had it blank out while riding. Just lucky, I guess?!

I presume you meant it froze up on the V 5.1.0 release, not the new V 6.1.0 release. Well I hope that's what you meant?

 

[jfischer]

Weird, what release does your bike tell you it has?

Mine says it's on 4.1.0

 

[mecsw500]

Mine says it's on 4.1.0

It should be finding at least one update.

I’ve no idea if you have to update from V 4.1.0 to V 5.1.0 and the to V 6.1.0, or whether you can go straight from V 4.1.0 to V 6.1.0.

In either case, V 6.1.0 is for a NHTSA mandated recall campaign so you very likely want to be on that release ASAP.

If it cannot find any updates, I would book an appointment with your dealer to get it done. It should be no charge and take less than 30 minutes to do.

As an aside, make sure your WiFi network is not open and has WSA2 or more security set.

 

[jfischer]

It should be finding at least one update.

I’ve no idea if you have to update from V 4.1.0 to V 5.1.0 and the to V 6.1.0, or whether you can go straight from V 4.1.0 to V 6.1.0.

In either case, V 6.1.0 is for a NHTSA mandated recall campaign so you very likely want to be on that release ASAP.

If it cannot find any updates, I would book an appointment with your dealer to get it done. It should be no charge and take less than 30 minutes to do.

As an aside, make sure your WiFi network is not open and has WSA2 or more security set.

I have tried 3 different WiFi networks including my phone's hotspot. It continues to just report no updates available.

 

[mecsw500]

I have tried 3 different WiFi networks including my phone's hotspot. It continues to just report no updates available.

Have you tried resetting the display to factory settings. It might be because there is some configurable it doesn't like that stops it searching correctly for the updates.

I'd do a reset to factory settings, then just try connecting again via your phone hotspot.

I cannot think of much else before taking it to the dealer for them to update it for you. It should be free as it is a safety recall.

 

[jfischer]

Have you tried resetting the display to factory settings. It might be because there is some configurable it doesn't like that stops it searching correctly for the updates.

I'd do a reset to factory settings, then just try connecting again via your phone hotspot.

I cannot think of much else before taking it to the dealer for them to update it for you. It should be free as it is a safety recall.

Yeah thought about that, but since nothing else is working I'll try the full reset. Won't lose much, other than my BT pairing to headset I guess.

EDIT: Multiple users on FB have confirmed that they are not getting the update presented to them either. I wonder if Can-AM is staging the rollout by VIN batches or something to prevent a mass bricking in the even of a bad update, or to prevent their servers from being overloaded. I think I'll just keep trying for a while and see if I eventually get it.

Second thought: Wondering now if those on v4.1.0 are not being presented with the upgrade. My small sample of users on FB are all on v4.1.0, including myself. Perhaps the upgrade from v4.1.0 is slightly different and that hasn't been released, or it's not even going to work? Has everyone that has gotten the upgrade for sure been on v5.1.0 before the latest update?

 

[mecsw500]

Perhaps like you say, BRP are staging the update availability?

If the bugs driving the recall weren't in V 4.1.0 then perhaps they are doing the V 5.1.0 updates first as that is where the liability lies?

If you go on to the Can Am website there is a form to fill in to ask BRP questions. I have used this in the past and they have been pretty quick to respond. I asked for the XPS Full Synthetic Oil safety sheet which they are obliged to give upon request, and I got a response within 24 hours.